Archives

Sunstar FAQ

Frequently Asked Questions

  • What is an ODS and how does it work? The ODS is an oxygen detection safety pilot system. It is designed to shut off the gas supply to the heater if the oxygen content in the room drops to 18% from a normal 21%+. In this event, the pilot flame actually lifts off the thermocouple cooling it down and causing the gas valve to close and the heater to shut off. Also, each ODS has a tamper-resistant pilot orifice assembly, so do not try to drill or clean out the ODS pilot with a hard object as you will damage it. Follow the cleaning instructions located below.
  •  How do I clean the ODS pilot assembly? If your pilot will not stay lit, try cleaning it. Use a can of compressed air, such as is used to clean a computer, to blow dust out of the pilot assembly. Sometimes just blowing air back through the pilot will get rid of the dirt.If that fails, turn off the gas supply to the heater. As indicated in Figure 5 below grab nut A with an open -end wrench and loosen nut B from the pilot tubing with another small adjustable wrench. Blow air pressure through the holes as indicated. This should blow out any foreign materials. To reassemble, tighten nut B by grabbing nut A with the open-end wrench. WARNING: When the heater is reassembled, always check for gas leaks. Apply a soap and water solution to all joints and watch for bubbles to check for gas leaks. Never use any open flame to check for gas leaks. 
    If that fails, you need to remove the orifice from the pilot burner cartridge using your wrenches to unscrew the orifice (Item A) and blow air through the pilot burner as shown in Figure 5. If the pilot burner remains blocked you will need to use a soft brush (pipe cleaner will also work) to dislodge a spider web or other obstruction. To prevent damage to this assembly, follow the instructions below for disassembly and assembly of the ODS for cleaning.
    WARNING: Never use needles, wires, or similar cylindrical objects to clean the pilot orifice. This will only damage the calibrated pilot orifice (about the size of the head of a pin) which controls the pilot gas flow. Simple rinsing with water and blowing air over it should clean the orifice.
  • How does this SunStar Corcho Model CK18 heater work again? (Applies to Manual ONLY) It’s slightly different than some 3-plaque heaters you may have seen previously. Instead of turning on the pilot and then one, two, and three plaques, the SunStar Corcho Model CK18 uses just two burner chambers and operates first on the single plaque burner. After the single plaque comes on, the double plaque is turned on giving you three full plaques of operation. If only two plaques are needed, then the double plaque burner may shut off leaving just one plaque burning.
  • Can a SunStar Corcho heater be converted to Natural or Propane Gas? No, each heater is specifically designed to work on either Natural Gas or Propane Gas. Each heater is certified only for use with the type of gas indicated on the heater nameplate (data plate). It is not designed for use with other gasses and is not convertible to use with other gasses.
  • Why doesn’t it need electricity? Each SunStar Corcho heater is equipped with a thermocouple incorporated in the ODS assembly. This is also the flame failure safety system. The heat from the pilot light warms the thermocouple and the dissimilar metals in the thermocouple react to the heat from the pilot flame and create a small amount of electricity (e.g. millivolts of electricity). This electricity from the heat is then used to energize a magnet in the gas valve to open it against the tension created by a spring in the gas valve. This allows gas to go to the burners. When the pilot flame is extinguished and is no longer generating heat on the thermocouple and, thereby, millivolts of electricity, the magnet de-energizes and the spring shuts the valve off. This is designed to turn off all the gas to the burner and pilot system. The use of this safety system and the gas fuel are the reasons that no electricity is needed to operate a SunStar Corcho heater. This product will still provide heat to your home even during power outages.
  • Can these heaters be installed in bedrooms or bathrooms? Only the model CK-6 (rated at 6,000 Btu’s) can be installed in a bathroom. Both the CK-6 and the CK-10 (rated at 9,500 Btu’s) can be installed in bedrooms. All other models are too big. The National Fuel Gas Code (NFPA 54) permits wall mounted installation of vent-free gas heaters of 10,000 Btu’s or less in bedrooms and 6,000 Btu’s or less in bathrooms. Please check with your gas supplier to determine if the installation of these heaters in bedrooms and bathrooms are permissible by your state and local codes.
  • Can this heater be installed in mobile homes? Yes, this heater may be installed in what’s termed “aftermarket” manufactured (mobile) homes where it is not prohibited by state or local codes. An “aftermarket” mobile home is defined as any type of mobile home that has already been sold to an end user or homeowner. It cannot be installed in a new mobile home on the dealer’s lot before it has been sold, but it can be installed in any mobile home after it has been sold (e.g. aftermarket). When installing this heater in a mobile home, the same safety rules of confined and unconfined spaces and clearance to combustible materials should be followed.

SunStar Corcho Heater Factory Warranty

10 year Limited Ten-Year Warranty

SunStar Heating Products, Inc. (SunStar) warrants SunStar Corcho gas heaters to be free from defects in workmanship and materials present at the time of shipment from the factory for a period of ten (10) years from the date of purchase by the original purchaser. The purchaser’s sole remedy under this limited warranty is as follows: If a purchaser discovers and reports to SunStar or the SunStar Corcho dealer/distributor a defect covered under this warranty within ninety (90) days from the date of purchase, SunStar or the SunStar Corcho dealer/distributor will, at the purchaser’s option and upon proof of purchase (including model and serial number) repair or replace the defective unit. If a purchaser discovers and reports to SunStar or the SunStar Corcho dealer/distributor a defect covered under this warranty more than ninety (90) days but less than three (3) years from the date of purchase, SunStar or the SunStar Corcho dealer/distributor will provide the purchaser at no charge and upon proof of purchase (including model and serial number) with parts necessary to repair the unit; or, if the purchaser first notifies and receives approval from and thereafter promptly returns (at the purchasers’ expense) the defective unit to SunStar’s SunStar Corcho Service Center (see phone contact below) SunStar will repair or replace, at SunStar’s option, the defective unit and return it to purchaser at no additional charge. If a purchaser discovers and reports to SunStar or the SunStar Corcho dealer/distributor a defect covered under this warranty more than three (3) years but less than ten (10) years from the date of purchase, SunStar shall, upon written notice to SunStar, (including model and serial number) provide the purchaser with parts necessary to repair the unit at no additional charge; provided the purchaser returns any defective parts needing replacement to SunStar’s SunStar Corcho Service Center (as provided for below) at the purchaser’s expense.

Duties Of The Owner

The heating appliance must be installed by a qualified installer and operated in accordance with the written instructions furnished with the appliance. Ready access to the appliance for service is the responsibility of the owner. Travel, diagnostic cost, service labor, labor to repair the defective appliance and freight charges on warranty parts to the factory will be the responsibility of the owner after the first 90 days of ownership have expired. A bill of sale, canceled check, or payment record should be kept to verify purchase date and remaining warranty period. Original carton should be kept for warranty return of the unit.

What Is Not Covered

This warranty does not imply or assume responsibility for consequential damages that may result from the use, misuse or improper installation of this heating appliance and in no event shall SunStar be responsible for such damages. This warranty does not cover claims, which do not involve defective workmanship or materials.

Your Rights Under State Law

This warranty gives you specific legal rights and you may also have other rights, which may vary, from state to state.

How To Get Service

All parts or products returned due to defects must be shipped prepaid to an Authorized SunStar Corcho Service Center. Please contact your SunStar Corcho dealer for service details or to obtain return authorization. If, after contacting your SunStar Corcho dealer, service received has not been satisfactory, contact: SunStar Corcho Service Center, SunStar Heating Products, Inc., P.O. Box 36271, Charlotte, NC 28236 or call at (704) 372-3486.

SunStar Corcho Gas Infrared Heaters

SunStar Gas Infrared Heaters

Click Here For Our Shop & Construction Site InfraRed Heaters

Click Here For Patio InfraRed Heaters

Free Shipping to the 48 Inland States
The SunStar Corcho line has been designed with many options and features including:
  • Manual & Thermostat Models
  • ODS & Flame Failure Safety Features
  • No Electricity Needed-Works Even During Power Outage
  • Wall Mount or Floor Mount, As Needed
  • Optional Blowers Available With Manual or Automatic Controls
  • Can Be Installed In Mobile Homes As Permitted By State and Local Codes
Scroll for Optional Accessories.
CK6 Infra Red Heater
CK10 Infra Red Heater
SC18 Infra Red Heater
SC30 Infra Red Heater

Scroll for Specifications              Frequently Asked Questions

Model SC 6
Model SC 10
Model SC 18
Model SC 30
Manual Only
Model SC 10 T
Model SC 18 T
Model SC 30 T
Manual
With Thermostat
Manual
With Thermostat
Manual
With Thermostat
Manual
With Thermostat
N/A
N/A
$230
$310
$257
$339
$340
$389
5 YEAR WARRANTY
When Placing An Order: Specify Type Gas To Be Used – Natural Gas or Propane
Note: The suffix “T” is used to designate thermostatically-controlled models.
6,000 BTU Model – Manual Only Available

Includes UPS Free Shipping to the 48 Inland States
Free Shipping to the 48 Inland States
We  Confirm  Your  Total  Cost  On  All  Orders  Prior  To  Shipping

Optional Accessories For SunStar Infrared Heaters

Floor Base
Blower Accessory
Optional Floor Base for Models CK6 & CK10
$36
No Optional Floor Base Needed for
Models SC 18 & SC 30
Optional Blower Accessory For Models SC18& SC30
$89
Optional Blower Not Available
For Models CK6 & CK10
ODS System
Oxygen Depletion System automatically
extinguishes flame and gas flow if oxygen
drops to unsafe levelsTEN YEAR Limited Warranty
See Actual Factory Warranty HerePUSHBUTTON IGNITER
Effortless push-button spark pilot lighter

Optional Automatic Thermostat
For comfort and fuel economy, with automatic pilot shutoff valve

Efficiency

99.9% Fuel efficient
Requires no flue and easy to install
Operates for pennies an hour
No electricity required

Optional Blower (Squirrel Cage Type)
Available as an accessory
(requires 115 volt electricity)

 

Vent Free Heaters
ARE NOT APPROVED
IN SOME AREAS OF THE
FOLLOWING STATES
California, Colorado, Massachusetts,
Minnesota, Montana, New York, Utah,
New Mexico

* Because states, counties, and municipalities adopt various codes, please check with your installer or local code officials to assure the current code in the city where you plan to install permits vent-free gas appliances.

While most states permit installation of vent-free gas heating appliances, a handful of states still prohibit residential use. Very often, that’s because a state’s building codes haven’t caught up with vent-free gas technology.
Currently seven states prohibit residential use: Alaska, Massachusetts, Montana, Minnesota *, Colorado *, Utah *, and California. However, many local and state codes are currently being revised to reflect acceptance of this new technology.
Click for map of states

* Several counties and municipalities in Colorado and Utah permit the product. Wisconsin restricts installation in homes built after 1980

 

Infrared Heating Plaque
Infrared Plaque Heaters Radiate Heat
And “Warms like the Sun”
Quickly Warms People & Objects
Before Heating The Air
Oxygen Depletion System
ODS System
Oxygen Depletion System
Cuts Off Gas & Burner
If Oxygen Falls Below Safe Levels
Sparke Ignition
Matchless Spark Ignition

Specifications

Model Number
CK-6
CK-10
SC-18
SC-30
Max BTU Input/NG
6,000
9,500
18,000
30,000
Max BTU Input/LPG
6,000
9,500
16,500
27,000
Dimensions:
Width
13″
13″
20″
23 2/3″
Depth
5 3/8″
5 3/8″
9 2/3 “
9 2/3″
Height
20 7/8″
20 7/8″
24 2/3 “
27 3/4″
Shipping Weight
13 lbs
13 lbs
24 lbs
32 lbs
Minimum Clearance from Combustible Material:
Top
36″
36″
36″
36″
Sides
6″
10″
13″
13″
Bottom ( Wall Mount)
2″
2″
2″
2″
Optional Accessories
Floor Stand
Yes
Yes
Included
Included
Blower/Fan
No
No
Yes
Yes

SunStar Construction Heating Products

Free Shipping to the 48 Inland States

RCH series

  • Ideal for construction sites, unheated work areas and supplemental heat in a large building.
  • Infrared heat when you need it, where you need it.
  • Heats people and work area directly…before heating the air.
  • No electricity is required.

Heavy Duty Infrared Heat

SunStar’s infrared construction heaters provide exceptional on-the-job versatility. These tough, reliable and job proven heaters are packed with features for both economy and rugged endurance. Built with heavy gauge steel they are designed to withstand continuous seasonal use even in severe industrial and construction type environments.

RCH100-N9A Nat Heater
RCH100-L9A LP Heater
$444.00
$444.00
Specify Type Gas to be used
Natural or Propane
Includes UPS Free Shipping to the 48 Inland States
Free Shipping to the 48 Inland States
We  Confirm  Your  Total  Cost  On  All  Orders  Prior  To  Shipping

RCH100-N9A
(nat gas w/t-stat control)RCH100-L9A
(LP gas w/t-stat control)Scroll Down for
Specifications

Typical Applications

Construction Sites Workshops
Unheated Work Areas Partially Open Buildings
Emergency Heat Thawing And Freeze Protection

Features

  • No electrical supplied
  • Lightweight for easy transportation
  • Stainless steel emitter
  • Compact 14″ diameter base
  • No moving parts
  • Optional 10 ft. hose and LP tank regulator with POL fitting available for LP units
  • Optional 15 ft. hose assembly available for natural gas units
  • 100% gas shutoff safety control

Specifications

Model Number
RCH100-N9A
RCH100-L9A
Max BTU Input/NG
100,000
Max BTU Input/LPG
95,500
Dimensions:
Height
32 1/2″
32 1/2″
Base
14″ Round
14″ Round
Shipping Weight
40 lbs
40 lbs
Area Coverage
1500-2500 sq. ft (depending on building heat loss)
Minimum Clearance from Combustible Material:
Top
54″
54″
Sides
60″
60″
Burner Pressure
3.5″ WC
10″ WC
Burner Pressure
5″ WC Minimum
14″ WC Maximum
11″ WC Minimum
14″ WC Maximum

SunStar Patio InfraRed Heaters

Free Shipping to the 48 Inland States

PH series

Enjoy Your Outdoors Longer with a
SunStar Patio Heater PATIO HEATERS

  • SunStar infrared patio heaters provide a 360-degree circle of radiant warmth.
  • No electricity is required.
  • Portable wheel kit is included.4 cup holders in
  • 4 cup holders in the base (each holds up to a 32 oz. cup).
  • Sleek design comes in stainless steel finish or black and silver texturized painted model.
  • Professional performance. Provides a powerful 40,000 Btu/hr.
  • UL listed and safety certified. Includes a flame failure safety device as standard.
  • Has weighted base to help prevent tip over and accepts a standard 20 lbs. cylinder.
  • Uniformly distributes heat in a 20′ diameter circle.
  • Convenient, matchless piezo ignition system.
PHS40-L6 Stainless Heater
PHS40-J6 Blk/Silver Heater
$459.00
$396.00
Includes UPS Free Shipping to the 48 Inland States

Free Shipping to the 48 Inland States

We  Confirm  Your  Total  Cost  On  All  Orders  Prior  To  Shipping

Specifications

I & O Instructions

Stainless Patio Heater
PHS40
Stainless Steel Model


PHJ40
Black & Silver Model